The point of this work is to guide you on the way to correctly bind a document using a thermal binding machine. If you have access to 5 or 6 thermal binding covers, follow thru these binding directions. If not, read through the material and try binding some documents later on.
After making sure that your machine is plugged in and turned on select a smaller thermal binding cover i.e. 1/16", 1/8" or 1/4" and the rough amount of paper needed to fit into the cover. In standard use, the operator will have a document of "x" number of sheets, which should then define the right size of thermal cover to use. The best way to do this is to place the paper, indexes, and so on. To be bound flat on a table and measure the thickness of the stack with a ruler. Choose a cover that meets that measurement. I.e. If you've a 1/4" pile of paper, you would utilise a 1/4" thermal binding cover. If you're between sizes, go to the following largest size.
1. To reduce static electricity that builds up between sheets run off a copier, the paper to be bound must be fanned. Take a heap of paper, and practice fanning using the following technique:
- Grasp the sheets on each side, holding them fairly loose.
- Bend the sheets as in the following diagram. While bent, exert pressure on the paper with your thumbs and fingers to gain a strong grip where the sheets cannot move.
- While maintaining force on the sheets, straighten out the stack of paper. This can bow the sheets so that there is air space between sheets. After air has been authorized into the sheets, release your grasp on the sheets as you jog them onto a flat, level surface. This is called fanning the paper. It is generally not necessary unless the paper has just come off a copier, where the pages contain a large amount of static electricity.
- Remember, it's the binding edge of the sheets which must always be uniformly jogged for a secure bind.
2. Place the thermal binding cover in your left hand (if you're right handed), and permit it to barely fall open to create what looks like a wide V. Insert the fanned sheets into your scored thermal binding cover (make sure that you grasp the sheets firmly to maintain the uniform jogged edge). The sheets should be targeted in the cover and placed on the adhesive backbone. Close the cover round the sheets. The 1st and last sheets shouldn't stick up higher than the other pages. If you have uneven pages, take all the sheets out of the cover, rejog them and insert them back into the cover.
3. Next, place the document (spine side down) so the fringe of the thermal cover is at the right side of the binding slot. The binding machine should mechanically start and dependent on the dimensions of your document should decide the length of the bind time.
4. When you remove the bound document, tap the backbone on the table to help set the adhesive, and set the document (s) on the cooling stand to maintain the square spine during curing. Make sure the document (s) are placed squarely on the cooling stand so that the spine remains square during the curing process. This will supply the most professional looking finished product.
5. The document must cool before it can be used. It should remain on the stand for 3 to 5 minues. This period of time varies depending on the thickness of the thermal binding cover. Glaringly, a 1/16" thick document will cool quicker than a 2" document. In the end any thermal cover, irrespective of size, will have reached full binding strength once the backbone is cool to the touch (roughly 15 minutes).
After making sure that your machine is plugged in and turned on select a smaller thermal binding cover i.e. 1/16", 1/8" or 1/4" and the rough amount of paper needed to fit into the cover. In standard use, the operator will have a document of "x" number of sheets, which should then define the right size of thermal cover to use. The best way to do this is to place the paper, indexes, and so on. To be bound flat on a table and measure the thickness of the stack with a ruler. Choose a cover that meets that measurement. I.e. If you've a 1/4" pile of paper, you would utilise a 1/4" thermal binding cover. If you're between sizes, go to the following largest size.
1. To reduce static electricity that builds up between sheets run off a copier, the paper to be bound must be fanned. Take a heap of paper, and practice fanning using the following technique:
- Grasp the sheets on each side, holding them fairly loose.
- Bend the sheets as in the following diagram. While bent, exert pressure on the paper with your thumbs and fingers to gain a strong grip where the sheets cannot move.
- While maintaining force on the sheets, straighten out the stack of paper. This can bow the sheets so that there is air space between sheets. After air has been authorized into the sheets, release your grasp on the sheets as you jog them onto a flat, level surface. This is called fanning the paper. It is generally not necessary unless the paper has just come off a copier, where the pages contain a large amount of static electricity.
- Remember, it's the binding edge of the sheets which must always be uniformly jogged for a secure bind.
2. Place the thermal binding cover in your left hand (if you're right handed), and permit it to barely fall open to create what looks like a wide V. Insert the fanned sheets into your scored thermal binding cover (make sure that you grasp the sheets firmly to maintain the uniform jogged edge). The sheets should be targeted in the cover and placed on the adhesive backbone. Close the cover round the sheets. The 1st and last sheets shouldn't stick up higher than the other pages. If you have uneven pages, take all the sheets out of the cover, rejog them and insert them back into the cover.
3. Next, place the document (spine side down) so the fringe of the thermal cover is at the right side of the binding slot. The binding machine should mechanically start and dependent on the dimensions of your document should decide the length of the bind time.
4. When you remove the bound document, tap the backbone on the table to help set the adhesive, and set the document (s) on the cooling stand to maintain the square spine during curing. Make sure the document (s) are placed squarely on the cooling stand so that the spine remains square during the curing process. This will supply the most professional looking finished product.
5. The document must cool before it can be used. It should remain on the stand for 3 to 5 minues. This period of time varies depending on the thickness of the thermal binding cover. Glaringly, a 1/16" thick document will cool quicker than a 2" document. In the end any thermal cover, irrespective of size, will have reached full binding strength once the backbone is cool to the touch (roughly 15 minutes).
About the Author:
Thanks for listening. I have an article here about selecting a seo expert, and another about Samsung Ram.